- Capacity:Up to 2000 Cu Ft
- Size:46.4w x 14.4d x 13.2h (in)
- Weight:161 lb
- Shipping Weight:200 lb
- Power/Rating:115V AC / 60 Hz
Condensing Unit Dimensions:
- 76 lbs
- 16.8w x 20.8d x 14h
Evaporator Unit Dimensions (including brackets):
- 85 lbs
- 46.4w x 14.4d x 13.2h
- Startup: 51.0 Amps
- Unit Amp Rating: 18.2 Amps (high fan speed)
- Total Watts: 1272 (med fan speed)
BTUH @ 55Â°F / Evaporator Decibels
- Low Fan Speed: 5961 / 54 dbA
- Med Fan Speed: 6346 / 58 dbA
- High Fan Speed: 6713 / 66 dbA
- 3/4 Ton Nominal
Condensing Unit Decibels
- Indoor: 67
Designed for wine cellars up to 2000 cubic feet and rated for internal or external (see notes below) applications, CellarPro's Mini-Split 8000S 3/4 Ton Nominal refrigeration system allows the noise from the condensing unit to be removed from living areas, and eliminates the need for large holes in your cellar wall. This is achieved by separating the evaporator unit from the condensing unit.
Only a few small openings for the line-set and drain line are required to connect the evaporator and condensing units. Inside the cellar, the evaporator unit is designed to mount on the wall near the top of the wine cellar. Outside the cellar, the condensing unit is attached to the evaporator unit by a line-set (sold separately) that can run up to 100 equivalent feet (and up to 30 vertical feet).
Our advanced evaporator unit uses a variable-speed centrifugal fan with three settings, including a "high" setting for maximum performance and a "low" setting for super-quiet operation. The evaporator should be mounted close to the ceiling inside the cellar.
Our high-performance condensing unit is designed to handle environments ranging from 0°F to 110°F. The condensing unit requires 12 inches of unobstructed space in front of the coils, and requires approx. 600-700 CFM of ventilation when installed in a confined space.
CellarPro Split wine cellar refrigeration systems offer a choice of wiring: 1. the Condensing unit can be electronically controlled by and wired to the Evaporator (single power source on the Evaporator side), or 2. the Condensing unit can be controlled by a Solenoid valve (dual power source, one each to the Evaporator and Condensing units.) The first choice (with electronic wiring) will allow the Condensing unit to be used in temperatures down to -20°F.
Important Notes: External installations require our outdoor hood (sold separately). For exposure to environments below 40°F, our compressor heatermodification is required. Access to the left and right side of the evaporator unit is required for installation. All split systems must be installed and charged on site by a qualified HVAC professional. Line-set equivalent feet must be calculated in accordance with ASHRAE guidelines; refer to our Line Sizing Chart for more information.
Capacity: Wine Cellars up to 2000 cubic feet with proper insulation and a moisture barrier.
Capacity: Up to 2000 cubic feet in properly insulated and sealed wine cellars.
- Up to 2000 Cu. Ft. Capacity (3/4 Ton Nominal)
- Engineered to operate in interior and external environments (0°F to 110°F)
- For temperatures below 40°F, our compressor heater modification is requred
- Schraeder Valve for Refrigerant Charge (R134A) and Superheat Adjustment
- Multiple Knock-Outs and Access Points
- Expansion Valve and Liquid Line Solenoid Valve (optional) come Factory Installed
- Choice of Single or Dual Power Supplies for Evaporator and Condenser Units
- Choice of Electronic or Valve Control for Condensing Unit
- Evaporator and Condensing Unit are Factory Pressurized and Shipped with Dry Nitrogen
- High-Performance Condensing Unit
- Variable Speed Evaporator Fan for Super-Quiet Operation or Max Performance
- Oversized Coated Evaporator Coils
- Adjustable Humidity Control via Digital Display
- 1/2" ID Drain Line
- 53 Decibels at Low Fan Speed (Evaporator)
- Electronic Thermostat, Digital LED Display and Audible/Visual Alarms
- Auto-Defrost Cycle
- Sight Glass and Liquid Line Filter/Drier
- Oversized Receiver for Long Line Sets
- Line-sets can run up to 100 equivalent feet (and up to 30 vertical feet)
- Adjustable Low Ambient Fan Cycling Control
- Auto Reset High Pressure Switch
- Compatible with a Dedicated 15-Amp Circuit
- Optional Bottle Probe
- Optional Outdoor Cover
- ETL Tested and Certified (UL Standards) (PENDING)
When ducting the FRONT of CellarPro VS and Split cooling units, varying amounts of condensation can occur depending on the ambient conditions where the cooling unit will be located. The charts above are designed to provide guidance in selecting the appropriate front duct kit depending on 1. Your desired cellar temperature, 2. The ambient temperature where the cooling unit will be located, and 3. the ambient relative humidity where the cooling unit will be located.
Condensation generally occurs on the cold surfaces of the face and around the front of the cooling unit when the temperature of the metal falls below the ambient dew point (a function of temperature and humidity). The greater the difference between the dew point and the metal temperature (ie the higher the dew point and the lower the metal temperature), the more condensation will occur. For this reason, CellarPro has developed two front duct kits for its VS and Split systems: a duct kit for LOW humidity conditions, and a duct kit for HIGH humidity conditions. The HIGH humidity duct kit has extra insulation around the front and face of the cooling unit, and always should be used together with our remote control display kit. In some cases (shown above in red), the humidity conditions are too high even for our HIGH humidity duct kit. In this case, the cooling unit should be moved to a conditioned space and the rear should be ducted if necessary.
1800 QTL / QT / XT / XTS: For five years from the date of purchase, your CellarPro warranty covers all parts and labor to repair or replace any components in the wine cooling unit that prove to be defective in materials or workmanship. Click here for information about our extended warranty.
1800 XT-220V: For two years from the date of purchase, your CellarPro warranty covers all parts and labor to repair or replace any components in the wine cooling unit that prove to be defective in materials or workmanship.
1800 XTSX, 3200 VSi/VSx, 4200 VSi/VSx: For five years from the date of purchase, your CellarPro warranty covers the internal compressor if it proves to be defective in materials or workmanship. In addition, for two years from the date of purchase, your CellarPro warranty covers all parts and labor to repair or replace any components in the wine cooling unit that prove to be defective in materials or workmanship. Click here for information about our extended warranty.
4200VSi / VSx - 220V/50Hz: For one year from the date of purchase, your CellarPro warranty covers all parts and labor to repair or replace any components in the wine cooling unit that prove to be defective in materials or workmanship.
Split Systems: For five years from the date of purchase, your CellarPro warranty covers the internal compressor if it proves to be defective in materials or workmanship. In addition, for two years from the date of original delivery, your CellarPro warranty covers all parts and labor to repair or replace any components in the wine cooling unit that prove to be defective in materials or workmanship. The warranty will not be activated until the Support and Data Service Sheet has been completed and submitted to CellarPro. The warranty period starts from the time of purchase, regardless of the time of activation.
For all products covered by the terms of this warranty, CellarPro will repair or replace the original cooling unit with a new or refurbished cooling unit and, once replaced, the original cooling unit must be returned to CellarPro.
All service provided by CellarPro under the above warranty must be performed by CellarPro or a designated repair facility unless otherwise specified by CellarPro. Purchaser is responsible for shipping the wine cooling unit to and from CellarPro or to and from a designated repair facility, and for removing and reinstalling the wine cooling unit from the wine cellar.
The limited warranty applies only to wine cooling units purchased from the factory or an authorized dealer. Damage caused by others or by any cause beyond the control of CellarPro, shall not be considered defects in material or workmanship and are not covered by the warranty. The limited warranty does not cover any parts or labor to correct any defect caused by negligence, commercial use, accident, or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES, WHICH CELLARPRO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. CELLARPRO WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIES OR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights, which vary from state to state.
To receive parts and/or service and the name of a CellarPro designated repair facility nearest you, contact your CellarPro dealer. You may also contact CellarPro directly by calling us at 1.877.726.8496.
No videos available for this product
- Cable Racks: 1 Week
- Glass and Cable: 1-2 Week
- RevueVino: 1 Week
- Whisperkool units: 1-2 Week
- CellarPro units: 1-2 Week
- Breezaire units: 1-2 Week
- Wine Guardian units: 1-2 Week
- WRR units: 1-2 Week
- Classic Kits: 3-4 Week
- Carpenter Kits: 3-4 Week
- Deluxe Metal Racks: 3-4 Week
- Modern Racks: 4-6 Week
- Glass Entryways: 4-6 Week
- Wooden Doors: 6-8 Week
- Metal Doors: 8-10 Week
- Vintner: 10-12 Week
- Custom: 12-14 Week
Some of our products have free shipping, while others have specific S&H charges. For those with free shipping note the Free Shipping applies only to the 48 contiguous states in the United States and APO addresses. Shipments to Alaska, Hawaii, island locations such as Martha's Vineyard that require a ferry to reach, and international shipments will most likely be subject to additional shipping. International shipment will most likely also incur duties and taxes.
Wine Rack Concepts uses various shipping methods to ensure that your racking and other purchases arrive to you when you need it, and free from damage. We utilize several different shipping carriers depending on your order size and where we are shipping your order to. Some of the carriers we choose to use are as follows, but not limited : Fed Ex, UPS, AIT, ABF, Seko, & Yellow. You will receive an email confirmation from us once your order has shipped from our facility advising you of the carrier and the tracking information, so you can plan for your delivery accordingly.
The following is for reference of larger orders or custom wine cellars:
Maximum Protextion of Your Order
Our custom cellars are boxed in corrugated with corner protectors, then stacked onto skids. The skids contain aprons around the perimeter as shown to minimize damage from fork lifts while being moved around shipping terminals and on/off the trucks. The vast majority of custom cellars ship via common carrier.
Means we ship via a 53' foot semi-trailer that will arrive at your residence and the driver will open the back of the truck and step aside for the assigned party on your end to unload it. If the basic service does not fit your needs we also have a host of additional services listed below that you can choose from for an additional cost.
Means that the client will be contacted when their product is completed and then we will arrange a mutually agreeable date and time for the product to be picked up.
Third party shipping
Means the customer has their own shipping company and is going to arrange for delivery of the product to their final destination at their expense. Wine Rack Concepts will need a completely filled out Bill of Lading at least 24 hours prior to the scheduled pick up date of the product. Product will be loaded on skids and customer will be charged a skid fee of $75 per skid. Client will be notified when their order is complete and ready for pick up and then we will arrange for a mutually agreeable date and time for the product to be picked up.
Inside Delivery and lift gate service
Means that the carrier will remove the product off of their truck and deliver it into your garage or the first room that is past the threshold of your residence or place of business. Lift gate service is required for them to take the product off the truck due to the length and weight of our product.
Needs to be marked if you live in one as there are only a limited number of specialty carriers who are willing to make deliveries to these communities due to the extra work involved in clearing a time for delivery and getting the clearance with security.
Is required if a 53' long semi trailer will not be able to make a delivery to park in front of your home or in your driveway at the time of delivery.
Two man delivery service
Will be needed if we are shipping product this in excess of 70 pounds per box or if you have requested delivery of your product inside your home to a location other than the first room pass the threshold of your residence or place of business.
Turn Key Quote
A Turn Key quote will be required if delivery is to be made to the following
- High Rise
- Any residential area where trucking companies must use asn elevator
- If the customer wants delivery past the threshold inside the residence.
- If the drop off location is not directly off of the driveway or if the driveway is inaccessible.